HP Compaq dx7300 Page 131 Reference Manual Download

Page: 131 / 234

Service Reference Guide, dx7300

433611-001

7–25

Removal and Replacement Procedures— Slim Tower (ST) Chassis

7.11.2 Optical Drive

CAUTION:

All removable media should be taken out of the drives before removing the drive from the

computer.

✎

An optical drive is a CD-ROM, CD-R/RW, DVD-ROM, DVD+R/RW, or CD-RW/DVD Combo
drive.

1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the lock (

Section

7.2

2. Prepare the computer for disassembly (

Section 7.1

3. Remove the computer cover (

Section 7.5

4. Rotate the drive cage to its upright position by pulling on the green-tabbed lip.

5. Disconnect the power and data cables from the rear of the optical drive.

Summary of Contents for Compaq dx7300











































































































































































































































Search results

Summary of Contents for Compaq dx7300

Reviews:

Related manuals for Compaq dx7300

Brands by name

Popular brands

HP Compaq dx7300, Reference Manual

Search results

Summary of Contents for Compaq dx7300

Reviews:

Related manuals for Compaq dx7300

Brands by name

Popular brands