manualshive.com logo in svg

HP Compaq dx7300, Reference Manual

The HP Compaq dx7300 user manual is an essential resource for getting acquainted with this versatile product. Obtain a comprehensive overview of its features and functions through this free manual download available at manualshive.com. Explore your device's potential and unleash its capabilities effortlessly with this user-friendly guide.

Share
Download
background image

Service Reference Guide, dx7300

433611-001

7–37

Removal and Replacement Procedures— Slim Tower (ST) Chassis

3. If reusing the existing heatsink, clean the bottom of the heatsink with the alcohol pad 

provided in the spares kit.

Ä

CAUTION: 

Before reinstalling the heatsink you must clean the top of the processor and the bottom of the 

heatsink with an alcohol pad supplied in the spares kit. After the alcohol has evaporated, apply thermal 

grease to the top of the processor from the syringe supplied in the spares kit.

4. Apply the thermal grease provided in the spares kit to the top of the processor and install the 

heatsink atop the processor.

5. Go to step 7.

6. If using a new heatsink, remove the protective covering from the bottom of the heatsink and 

place it in position atop the processor.

7. Secure the heatsink to the system board and system board tray with the 4 captive screws and 

attach the heatsink control cable to the system board. 

Ä

CAUTION: 

Heatsink retaining screws should be tightened in diagonally opposite pairs (as in an X) to 

evenly seat the heatsink on the processor. This is especially important as the pins on the socket are very 

fragile and any damage to them may require replacing the system board.

✎

After installing a new processor onto the system board, always update the system ROM to ensure 
that the latest version of the BIOS is being used on the computer. The latest system BIOS can be 
found on the Web at: 

http:\\h18000.www1.hp.com/support/files

.

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Contec PT-970 A Series Reference Manual preview
PT-970 A Series
Brand: Contec Pages: 77
Medion AKOYA P5320 E Quick Start Manual preview
AKOYA P5320 E
Brand: Medion Pages: 2
Avalue Technology BMX-T522-SK Quick Reference Manual preview
BMX-T522-SK
Brand: Avalue Technology Pages: 15
C&T VCO-6020-1050TI User Manual preview
VCO-6020-1050TI
Brand: C&T Pages: 79
Alienware 13 R3 Setup And Specifications preview
13 R3
Brand: Alienware Pages: 20
InHand InBox300 Series User Manual preview
InBox300 Series
Brand: InHand Pages: 28
ACE COMPUTERS Firestorm 1Z490X Technical Reference Manual preview
Firestorm 1Z490X
Brand: ACE COMPUTERS Pages: 42
Dell OptiPlex XE3 Setup Manual preview
OptiPlex XE3
Brand: Dell Pages: 38
Dell OptiPlex XE2 Owner'S Manual preview
OptiPlex XE2
Brand: Dell Pages: 61
Dell OptiPlex XE3 Service Manual preview
OptiPlex XE3
Brand: Dell Pages: 70
Dell Precision 450N Setup And Quick Reference Manual preview
Precision 450N
Brand: Dell Pages: 208
Dell Precision 8F765 Setup And Quick Reference Manual preview
Precision 8F765
Brand: Dell Pages: 260
Dell Precision 8F764 Setup And Quick Reference Manual preview
Precision 8F764
Brand: Dell Pages: 152
Dell Precision M2800 Owner'S Manual preview
Precision M2800
Brand: Dell Pages: 81
Dell Precision D490 Quick Reference Manual preview
Precision D490
Brand: Dell Pages: 124
Dell Precision 8T146 Setup And Quick Reference Manual preview
Precision 8T146
Brand: Dell Pages: 96
Dell Precision 9T217 Setup And Quick Reference Manual preview
Precision 9T217
Brand: Dell Pages: 170
Dell Precision K8642 Quick Reference Manual preview
Precision K8642
Brand: Dell Pages: 138

Brands by name

Popular brands

Load more brands