NEC POWERMATE P2166 Manual Download Page 1 | Manualshive

Page: 1 / 221

background image

First Printing — November 1996

Copyright 1996

NEC Computer Systems Division

Packard Bell NEC, Inc.

1414 Massachusetts Avenue

Boxborough, MA 01719-2298

All Rights Reserved

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related
materials, is the valuable property of NEC Computer Systems Division, Packard
Bell NEC, Inc. (hereinafter “NECCSD”) and/or its licensors. NECCSD and/or its
licensors, as appropriate, reserve all patent, copyright and other proprietary rights
to this document, including all design, manufacturing,reproduction, use, and sales
rights thereto, except to the extent said rights are expressly granted to others.

The NECCSD product(s) discussed in this document are warranted in accordance
with the terms of the Warranty Statement accompanying each product. However,
actual performance of each such product is dependent upon factors such as system
configuration, customer data, and operator control. Since implementation by
customers of each product may vary, the suitability of specific product
configurations and applications must be determined by the customer and is not
warranted by NECCSD.

To allow for design and specification improvements, the information in this
document is subject to change at any time, without notice. Reproduction of this
document or portions thereof without prior written approval of NECCSD is pro-
hibited.

NEC is a registered trademark of NEC Corporation and FastFacts, MultiSync, and PowerMate are either

trademarks or registered trademarks of NEC Technologies, Inc.; these trademarks are used under
license by Packard Bell, NEC.

All other product, brand, or trade names used in this publication are the trademarks or registered

trademarks of their respective trademark owners.

1
2
3
...
»

Summary of Contents for POWERMATE P2166






























































































































































































































Reviews:

No comments

Related manuals for POWERMATE P2166

Brand: IBM Pages: 52

Brand: Acer Pages: 51

Brand: Zotac Pages: 57

D-3362-I Series

Brand: Icop Pages: 14

Brand: EUROCOM Pages: 176

Brand: Acer Pages: 136

Brand: Acer Pages: 88

Brand: Dell Pages: 3

Brand: Ergo Pages: 33

Brand: Digital Equipment Pages: 61

Adaptec AHA-1742A

Brand: Digital Equipment Pages: 28

Brand: Display Mount Pro Pages: 6

Brand: Asus Pages: 60

Brand: Asus Pages: 62

Brand: Asus Pages: 62

Brand: Asus Pages: 66

Brand: Asus Pages: 68

Brand: Asus Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands