manualshive.com logo in svg

HP Compaq dx7300, Reference Manual

The HP Compaq dx7300 user manual is an essential resource for getting acquainted with this versatile product. Obtain a comprehensive overview of its features and functions through this free manual download available at manualshive.com. Explore your device's potential and unleash its capabilities effortlessly with this user-friendly guide.

Share
Download
background image

Service Reference Guide, dx7300

433611-001

D–3

Troubleshooting Without Diagnostics

Cannot remove 

computer cover or 

access panel.

Smart Cover Lock, 

featured on some 

computers, is locked.

1. Unlock the Smart Cover Lock 

using Computer Setup.

2. Use the Smart Cover FailSafe Key 

in case of forgotten password, 

power loss, or computer 

malfunction.

Poor performance is 

experienced.

Processor is hot.

1. Ensure airflow to the computer is 

not blocked. Leave a 10.2-cm 

(4-inch) clearance on all vented 

sides of the computer and above 

the monitor to permit the required 

airflow.

2. Ensure the fans are connected 

and working properly (some fans 

only operate when needed).

3. Ensure the processor heatsink is 

installed properly.

Hard drive is full.

Transfer data from the hard drive to 

create more space on the hard drive.

Low on memory.

Add more memory.

Hard drive fragmented.

Defragment hard drive.

Program previously 

accessed did not release 

reserved memory back to 

the system

Restart the computer.

Virus resident of the hard 

drive.

Run virus protection program.

Too many applications 

running.

1. Close unnecessary applications.

2. Add more memory.

Some software 

applications, especially 

games, are stressful on the 

graphics subsystem.

1. Lower the display resolution for 

the current application or consult 

the documentation that came with 

the application for suggestions on 

how to improve performance by 

adjusting parameters in the 

application.

2. Add more memory.
3. Upgrade the graphics solution.

Cause unknown.

Restart the computer.

Solving Minor Problems 

(Continued)

Problem

Cause

Possible Solution

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Medion AKOYA P5320 E Quick Start Manual preview
AKOYA P5320 E
Brand: Medion Pages: 2
Gigabyte GB-AEDNK User Manual preview
GB-AEDNK
Brand: Gigabyte Pages: 34
Craftsman Essentio CG5275 User Manual preview
Essentio CG5275
Brand: Craftsman Pages: 26
Craftsman 714.68658 User Instructions preview
714.68658
Brand: Craftsman Pages: 8
Sharp PC-4702 Service Manual preview
PC-4702
Brand: Sharp Pages: 83
Sharp PC-1500A Instruction Manual preview
PC-1500A
Brand: Sharp Pages: 168
GIGAIPC QBiX Series Manual preview
QBiX Series
Brand: GIGAIPC Pages: 70
Fujitsu Siemens Computers SCENIC S 2 Operating Manual preview
SCENIC S 2
Brand: Fujitsu Siemens Computers Pages: 72
Fujitsu Siemens Computers CELSIUS M430 Operating Manual preview
CELSIUS M430
Brand: Fujitsu Siemens Computers Pages: 90
Fujitsu Siemens Computers CELSIUS M Operating Manual preview
CELSIUS M
Brand: Fujitsu Siemens Computers Pages: 92
Viglen Omnino HS User Manual preview
Omnino HS
Brand: Viglen Pages: 45
VTech Creativision Instruction Manual preview
Creativision
Brand: VTech Pages: 8
VTech DESKPRO User Manual preview
DESKPRO
Brand: VTech Pages: 22
IAC INDUSTRIES QS-SMS Assembly Instructions Manual preview
QS-SMS
Brand: IAC INDUSTRIES Pages: 44
Aaeon BOXER-6616 User Manual preview
BOXER-6616
Brand: Aaeon Pages: 116
Radio Shack TRS-80 Model 4 Introduction Manual preview
TRS-80 Model 4
Brand: Radio Shack Pages: 42
Quanmax QDSP-1000 User Manual preview
QDSP-1000
Brand: Quanmax Pages: 31
Vector Graphic Bitstreamer II User Manual preview
Bitstreamer II
Brand: Vector Graphic Pages: 54

Brands by name

Popular brands

Load more brands