manualshive.com logo in svg

HP Compaq dx7300, Reference Manual

The HP Compaq dx7300 user manual is an essential resource for getting acquainted with this versatile product. Obtain a comprehensive overview of its features and functions through this free manual download available at manualshive.com. Explore your device's potential and unleash its capabilities effortlessly with this user-friendly guide.

Share
Download
background image

Service Reference Guide, dx7300

433611-001

7–17

Removal and Replacement Procedures— Slim Tower (ST) Chassis

7.9.3  PCI Express Expansion Card

To remove a PCI Express expansion card:

1. If you have locked the Smart Cover Lock, restart the computer and enter Computer Setup to 

unlock the lock.

2. Turn off the computer properly through the operating system, then turn off any external 

devices.

3. Disconnect the power cord from the power outlet and disconnect any external devices.

4. Remove the computer cover. (

Section 7.5

).

5. Release the slot cover retention latch on the back of the computer that secures the PCI slot 

covers by lifting the green tab on the latch and rotating the latch to the open position.

6. Pull the retention arm on the back of the PCI Express expansion socket away from the card 

(on x16 card socket only) and carefully rock the card back and forth until the connectors pull 
free from the socket. Pull the expansion card straight up from the socket then away from the 
inside of the chassis. Be sure not to scrape the card against the other components.

7. If you are not installing a new expansion card, install an expansion slot cover to close the 

open slot.

8. Rotate the slot cover retention latch back in place to secure the expansion cards and 

expansion slot covers.

Ä

CAUTION: 

All expansion card slots on the rear of the computer must contain either an expansion card 

or slot cover for proper cooling of internal components during operation.

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Hach TitraLab KF1000 Series User Manual preview
TitraLab KF1000 Series
Brand: Hach Pages: 68
Hach TitraLab AT1102 Basic User Manual preview
TitraLab AT1102
Brand: Hach Pages: 158
IBM NetVista A22p Kurzübersicht preview
NetVista A22p
Brand: IBM Pages: 78
IBM NetVista A22p Manual D'Utilisation preview
NetVista A22p
Brand: IBM Pages: 90
Vecow ECS-9671 GTX950 User Manual preview
ECS-9671 GTX950
Brand: Vecow Pages: 111
IBM 6868 - IntelliStation M - Pro User Manual preview
6868 - IntelliStation M - Pro
Brand: IBM Pages: 188
PRESONUS FIREBOX User Manual preview
FIREBOX
Brand: PRESONUS Pages: 8
Jupiter H310 Quick Installation Manual preview
H310
Brand: Jupiter Pages: 2
Sony VAIO PCV-RX480DS Specifications preview
VAIO PCV-RX480DS
Brand: Sony Pages: 1
Sony VAIO PCV-RX651 Specifications preview
VAIO PCV-RX651
Brand: Sony Pages: 2
Sony VAIO PCV-RX470DS Specifications preview
VAIO PCV-RX470DS
Brand: Sony Pages: 1
Sony VAIO PCV-RX312 Specifications preview
VAIO PCV-RX312
Brand: Sony Pages: 3
Sony VAIO PCV-RS402 Software Manual preview
VAIO PCV-RS402
Brand: Sony Pages: 45
Sony Vaio PCV-RS602 Software Manual preview
Vaio PCV-RS602
Brand: Sony Pages: 57
Sony Vaio PCV-RS702 Software Manual preview
Vaio PCV-RS702
Brand: Sony Pages: 61
Sony VAIO PCV-RS302 Software Manual preview
VAIO PCV-RS302
Brand: Sony Pages: 50
Sony VAIO PCV-2200 Quick Start Manual preview
VAIO PCV-2200
Brand: Sony Pages: 40
Sony VAIO PCV-D11M Hardware Manual preview
VAIO PCV-D11M
Brand: Sony Pages: 57

Brands by name

Popular brands

Load more brands