HP Compaq dx7300 Page 18 Reference Manual Download

Page: 18 / 234

2–8

433611-001

Service Reference Guide, dx7300

Setup Utilities and Diagnostics Features

Storage

(continued)

Boot Order

Allows you to:

• Specify the order in which attached devices (such as a USB

flash media device, diskette drive, hard drive, optical drive, or

network interface card) are checked for a bootable operating

system image. Each device on the list may be individually

excluded from or included for consideration as a bootable

operating system source.

• Specify the order of attached hard drives. The first hard drive in

the order will have priority in the boot sequence and will be

recognized as drive C (if any devices are attached).

✎

MS-DOS drive lettering assignments may not apply after a

non-MS-DOS operating system has started.

Shortcut to Temporarily Override Boot Order

To boot

one time

from a device other than the default device

specified in Boot Order, restart the computer and press

when the

monitor light turns green. After POST is completed, a list of bootable

devices is displayed. Use the arrow keys to select the preferred

bootable device and press

Enter

. The computer then boots from the

selected non-default device for this one time.

Security Smart

Card

Options (some

models)

Allows you to enable/disable the Smart Card to be used in place of

the Power-On Password. This option only appears if a Smart Card

reader is attached to the system.

Setup Password

Allows you to set and enables setup (administrator) password.

✎

If the setup password is set, it is required to change Computer

Setup options, flash the ROM, and make changes to certain plug

and play settings under Windows.

Power-On

Password

Allows you to set and enable power-on password. The power-on

password prompt appears after a power cycle. If the user does not

enter the correct power-on password, the unit will not boot.

✎

This password does not appear on warn boots, such as

CTRL+ALT+DEL

Restart from Windows

unless enabled

Password Options

below

Password Options

(This selection will

appear only if a

power-on

password or setup

password is set.)

Allows you to:

• Lock legacy resources (appears if a setup password is set)
• Enable/disable network server mode (appears if a power-on

password is set)

• Specify whether the password is required for warm boot

(

CTRL+ALT+DEL

) (appears if a power-on password is set)

• Enable/Disable Setup Browse Mode (appears if a setup

password is set) (allows viewing, but not changing, the F10

Setup Options without entering setup password)

Heading

Option

Description

✎

Support for specific Computer Setup options may vary depending on the hardware configuration.

Summary of Contents for Compaq dx7300











































































































































































































































Search results

Summary of Contents for Compaq dx7300

Reviews:

Related manuals for Compaq dx7300

Brands by name

Popular brands

HP Compaq dx7300, Reference Manual

Search results

Summary of Contents for Compaq dx7300

Reviews:

Related manuals for Compaq dx7300

Brands by name

Popular brands