manualshive.com logo in svg

HP Compaq dx7300, Reference Manual

The HP Compaq dx7300 user manual is an essential resource for getting acquainted with this versatile product. Obtain a comprehensive overview of its features and functions through this free manual download available at manualshive.com. Explore your device's potential and unleash its capabilities effortlessly with this user-friendly guide.

Share
Download
background image

Service Reference Guide, dx7300

433611-001

6–17

Removal and Replacement Procedures— Microtower (MT) Chassis

6.9 Drives

The computer supports up to six drives that may be installed in various configurations.

This Section describes the procedure for replacing or upgrading the storage drives. A Torx T-15 
screwdriver is needed to remove and install the guide screws on a drive.

Ä

CAUTION: 

Make sure personal files on the hard drive are backed up to an external storage device 

before removing the hard drive. Failure to do so will result in data loss. After replacing the primary hard 

drive, you will need to run the 

Restore Plus! CD

 to load the HP factory-installed files.

6.9.1 Drive Positions 

Drive Positions

Item

Description

1

Two 5.25-inch, half-height bays for optional drives

2

Two standard 3.5-inch, one-third height bays (1.44-MB diskette drives shown)*

3

Two internal 3.5-inch, one-third height bays for hard drives

*A 3.5-inch diskette drive or zip drive may be installed in this bay but the correct bezel must be 

installed to ensure proper air flow.

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Gateway Computer Reference Manual preview
Computer
Brand: Gateway Pages: 126
Gateway E-3600 System Manual preview
E-3600
Brand: Gateway Pages: 158
IBM IntelliStation Z Pro 6221 Installation Manual preview
IntelliStation Z Pro 6221
Brand: IBM Pages: 110
IBM Power 775 Service Procedure preview
Power 775
Brand: IBM Pages: 27
IBM IntelliStation 6866 Hardware Maintenance Manual preview
IntelliStation 6866
Brand: IBM Pages: 148
Acer Predator PO3-600 E Manual preview
Predator PO3-600 E
Brand: Acer Pages: 100
Digital Equipment VT18X Upgrade And System Test Manual preview
VT18X
Brand: Digital Equipment Pages: 61
Digital Equipment Adaptec AHA-1742A User Information preview
Adaptec AHA-1742A
Brand: Digital Equipment Pages: 28
BESTEK MEB-7601 Quick Manual preview
MEB-7601
Brand: BESTEK Pages: 11
Optoma OPS2-i7 Quick Install Manual preview
OPS2-i7
Brand: Optoma Pages: 2
Nexcom XPPC 22-100A User Manual preview
XPPC 22-100A
Brand: Nexcom Pages: 59
Nexcom NISE 107 Series User Manual preview
NISE 107 Series
Brand: Nexcom Pages: 73
Nexcom NIFE 105 Series User Manual preview
NIFE 105 Series
Brand: Nexcom Pages: 77
Nexcom NISE 50 User Manual preview
NISE 50
Brand: Nexcom Pages: 87
Nexcom 10J00372000X0 User Manual preview
10J00372000X0
Brand: Nexcom Pages: 85
UCI EasyPC Z-100 Series User Manual preview
EasyPC Z-100 Series
Brand: UCI Pages: 74
MSI MEGA MPC 915 User Manual preview
MEGA MPC 915
Brand: MSI Pages: 86
GARANT mLevel User Manual preview
mLevel
Brand: GARANT Pages: 60

Brands by name

Popular brands

Load more brands