manualshive.com logo in svg

HP Compaq dx7300, Reference Manual

The HP Compaq dx7300 user manual is an essential resource for getting acquainted with this versatile product. Obtain a comprehensive overview of its features and functions through this free manual download available at manualshive.com. Explore your device's potential and unleash its capabilities effortlessly with this user-friendly guide.

Share
Download
background image

7–38

433611-001

Service Reference Guide, dx7300

Removal and Replacement Procedures— Slim Tower (ST) Chassis

7.16 Speaker 

1. Prepare the computer for disassembly (

Section 7.1

).

2. Remove the computer cover (

Section 7.5

).

3. Remove the fan shroud

 

(

Section 7.12

).

4. Remove any memory modules that might interfere with the screwdriver used for removing 

the speaker.

5. Disconnect the speaker wire from the system board.

6. Remove the two screws

 

that secure the speaker to the chassis

1

.

7. Rotate the top of the speaker back to clear the lip on the top of the chassis, then lift the 

speaker up and out of the chassis

2

.

To install the speaker, reverse the removal procedures.

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Ace c3700 - Workstation Manual preview
c3700 - Workstation
Brand: Ace Pages: 21
CyberResearch CYRAQ PPC Series User Manual preview
CYRAQ PPC Series
Brand: CyberResearch Pages: 103
WinSystems SYS-ITX-N-3900 Product Manual preview
SYS-ITX-N-3900
Brand: WinSystems Pages: 53
IBM 6862 - PC 300 PL User Manual preview
6862 - PC 300 PL
Brand: IBM Pages: 208
Compaq Presario 3500 Series Maintenance & Service Manual preview
Presario 3500 Series
Brand: Compaq Pages: 68
Workrite Solace Sit-to-Stand Premium Assembly/Installation Instructions preview
Solace Sit-to-Stand Premium
Brand: Workrite Pages: 2
GREER Company MicroGuard 400 Service Training preview
MicroGuard 400
Brand: GREER Company Pages: 18
Fujitsu ESPRIMO Q5 Series Operating Manual preview
ESPRIMO Q5 Series
Brand: Fujitsu Pages: 61
Seametrics FT420 Instructions preview
FT420
Brand: Seametrics Pages: 4
Stanley STST98182-1 User Manual preview
STST98182-1
Brand: Stanley Pages: 23
Lenovo IdeaCentre 700 Series Quick Start Manual preview
IdeaCentre 700 Series
Brand: Lenovo Pages: 2
Lenovo ideacentre 620S Quick Start Manual preview
ideacentre 620S
Brand: Lenovo Pages: 2
Lenovo IdeaCentre 3015 Specification Sheet preview
IdeaCentre 3015
Brand: Lenovo Pages: 1
Lenovo ideacentre 720 User Manual preview
ideacentre 720
Brand: Lenovo Pages: 11
Lenovo IdeaCentre 310S-08IGM User Manual preview
IdeaCentre 310S-08IGM
Brand: Lenovo Pages: 8
Lenovo ideaCentre H505s Hardware Maintenance Manual preview
ideaCentre H505s
Brand: Lenovo Pages: 49
Lenovo ideaCentre H500s Hardware Maintenance Manual preview
ideaCentre H500s
Brand: Lenovo Pages: 51
Lenovo ideaCentre H500 Hardware Maintenance Manual preview
ideaCentre H500
Brand: Lenovo Pages: 51

Brands by name

Popular brands

Load more brands