manualshive.com logo in svg

HP 16533A, User Reference, Page: 64 / 152

Share
Download
HP 16533A User Reference Download Page 64

V Marker Value Display

Any time the markers (either voltage and/or time) are turned on, the current
marker settings may be displayed on the channel, trigger, display and
auto-measure menus by using the Display Options field located to the right
of the time base Delay field.  The Display Options field provides a pop-up
menu that allows you to select to set channel labels or to view the Sample
Period display or the Marker Value display.

The Marker Value display consists of two blocks. One contains settings for
the voltage markers, the second contains settings for the time markers.  If
only one set of markers is turned on, only one of the two blocks will appear
on the screen.

On the marker menu, if time markers are turned off, the Sample Period
display will appear on the Marker menu.  If time markers are selected as
either On or Auto, the Sample Period display is not visible on the Marker
menu.

The Display Options field never appears on the Marker menu.

The Marker Menu

V Marker Value Display

5-22

Summary of Contents for 16533A

























































































































































Reviews:

No comments