manualshive.com logo in svg

HP 16533A, User Reference, Page: 139 / 152

Share
Download
HP 16533A User Reference Download Page 139

7

Calibrate the Logic Trigger of the Self Cal.

a

Obtain a BNC 50-

Ω

, 9-inch cable.

b

Touch the Procedure field, then touch Logic Trigger from the pop-up
menu.

c

Touch the Start field and follow the instructions on the display.

d

After completion of the Logic Trigger calibration, remove the cable
from the instrument.

8

Calibrate Ext Trig Null of the Self Cal.

a

Connect a BNC 50-

Ω

, 9-inch cable to the BNC tee adapter.  Connect

the BNC 50

Ω

 (f)/SMB(m) adapter to one end of the BNC tee adapter

using a BNC(m)(m) adapter.  Once you touch Start, the instrument
will prompt you to connect the cables to the appropriate locations on
the rear panel of the instrument.

b

Touch the Procedure field, then touch Ext Trig Null from the pop-up
menu.

c

Touch the Start field and follow the instructions on the display.

d

After completion of External Trigger Null Calibration, remove the
cables from the instrument.

Protect the operational accuracy calibration factors

1

Remove power from the instrument.  Pull out halfway all cards and
filler  panels located above the oscilloscope, then remove the filler
panels and  cards located above the oscilloscope.

2

Remove the HP 16533/34A module and set the
PROTECT/UNPROTECT switch to the  PROTECT position. On a
multi-card module, the PROTECT/UNPROTECT switch on all  cards
must be set to PROTECT.

3

Reinstall the modules and filler panels.

Installation and Operator’s Service

Protect the operational accuracy calibration factors

11–15

Summary of Contents for 16533A

























































































































































Reviews:

No comments