manualshive.com logo in svg

HP 16533A, User Reference, Page: 114 / 152

Share
Download
HP 16533A User Reference Download Page 114

Delete All Field

The Delete All field in the Waveform Selection pop-up menu lets you delete
all of the currently displayed channel inputs from the waveform display area.
The pop-up selections for this field are Continue and Cancel

Cancel

Selecting Cancel from the Delete All pop-up menu allows you to change your
mind about deleting all currently displayed inputs.  Touching this field
causes the pop-up to disappear.  No changes are made to the display choices
made prior to touching the Delete All field.

Continue

Selecting Continue from the Delete All pop-up menu causes all of the
currently displayed inputs to be deleted.  Touching this field also causes the
pop-up to disappear.

Delete Field

The Delete field in the Waveform Selection pop-up menu lets you delete
channel inputs from the waveform display area.

Deleting a Channel 

You use the knob to highlight the input channel in the channel label field
that you want to delete.  You then touch the Delete field in the Waveform
Selection pop-up to delete the highlighted channel input from the channel
label field, and hence, from the waveform display area.  The input channel
highlighted in white will be deleted when you remove your finger from the
Delete field.  If you change your mind, slide your finger off the Delete field
before lifting it.

Labels Field

The Labels field in the Waveform Selection pop-up menu lets you pick the
channels you wish to display on the screen.  You use this field in conjunction
with the Action and Channel Mode fields to make your display choices when
running your mainframe modules independently.  For intermodule runs, you

The Waveform Selection Menu

Delete All Field

9-10

Summary of Contents for 16533A

























































































































































Reviews:

No comments