HP 16533A User Reference Download Page 121

Page: 121 / 152

HORIZONTAL:

Time Base Range:

0.5 ns/div to 5 s/div

Time base Resolution:

10 ps

Delay Pre-trigger Range:

81.8 sec, 5 divisions

Delay Post-trigger Range:

2.5 x 10

seconds

TRIGGERING:

Trigger Level Range:

Within display window (vertical /- 2

divisions)

Trigger Modes:

Immediate:

Triggers immediately after arming condition is met.

Edge:

Triggers on rising or falling edge from channel 1 or channel 2.

Pattern:

Triggers on entering or exiting a specified pattern across two

channels.

Auto Trigger:

Self-triggers if no trigger condition is found within

approximately 50 ms after arming.

Events Delay:

The trigger can be set to occur on the nth edge or pattern, as

specified by the user.

Intermodule:

Arms another measurement module or triggers the rear panel

BNC.

Specifications and Characteristics

Characteristics

10–5

Summary of Contents for 16533A

























































































































































Search results

Summary of Contents for 16533A

Reviews:

HP 16533A, User Reference, Page: 121 / 152

Search results

Summary of Contents for 16533A

Reviews: