manualshive.com logo in svg

HP 16533A, User Reference, Page: 55 / 152

Share
Download
HP 16533A User Reference Download Page 55

Slope Field

The Slope field sets the Tx or To marker on either the positive or negative
edge of the selected occurrence of a waveform.  When you touch the Slope
field, the slope toggles between Positive and Negative. 

The default selection for the Slope field is Positive.

Occur Field

The Occur field sets the Tx or To marker on a specific occurrence of a
displayed edge on the waveform.  You can define the edge to be displayed all
the way from the 1st edge up to the 100th edge. The count of edge
occurrences is made starting with the first edge displayed on the screen. 

Auto-marker measurements are made with data that is displayed on the
screen.  Make sure the data of interest is fully displayed on the screen.

When the Occur field is selected, you can change the occurrence by turning
the knob or by entering a new value from the pop-up keypad. The keypad
appears when you touch the Occur field when the field is light blue.  Any
number from 1 to 100 in increments of 1 can be entered. 

The default value for the Occur field is 1. 

The Marker Menu

Slope Field

5-13

Summary of Contents for 16533A

























































































































































Reviews:

No comments