manualshive.com logo in svg

HP 16533A, User Reference, Page: 137 / 152

Share
Download
HP 16533A User Reference Download Page 137

2

Calibrate Vert Cal of the Self Cal.

a

Connect two BNC 50-

Ω

, 9-inch cables to the BNC tee adapter.  Once

you touch Start, the instrument will prompt you to connect the cables
to the appropriate locations on the rear panel of the instrument.

b

Touch the Mode field, then touch Self Cal from the pop-up menu.

c

Touch the Procedure field, then touch Vert Cal from the pop-up menu.

d

Touch the Channel field, then touch All from the pop-up menu.

e

Touch the Start field and follow the instructions on the display.

f

After completion of Vertical Calibration, remove the cables from the
instrument.

3

Calibrate Delay of the Self Cal.

a

Obtain a BNC 50-

Ω

, 9-inch cable.  Once you touch Start, the

instrument will prompt you to connect the cable to the appropriate
location on the rear panel of the instrument.

b

Touch the Procedure field, then touch Delay from the pop-up menu.

c

Touch the Channel field, then select channel 1.

d

Touch the Start field and follow the instructions on the display.

e

Repeat steps c and d for channel 2.

f

After completing all of the channel delay calibrations, remove the
cable from the oscilloscope.

4

If a multi-card HP 16533/34A module is being calibrated, repeat steps
1 through 3  for the next HP 16533/34A card until all cards have been
completed.

5

If a single-card HP 16533/34A module is being calibrated, proceed to
step 6. If  a multi-card HP 16533/34A module is being calibrated,
perform the following steps  before proceeding to step 6.

a

Remove power from the HP 16500 mainframe.

Installation and Operator’s Service

Self Cal menu calibrations

11–13

Summary of Contents for 16533A

























































































































































Reviews:

No comments