HP 16533A User Reference Download Page 60 | Manualshive

Page: 60 / 152

HP 16533A User Reference Download Page 60

Voltage Markers Options

When you touch the V Markers field on the display, a pop-up menu
appears. When you touch the On field in the pop-up to turn Voltage
Markers On, you can manually move the Va and Vb markers to make
voltage measurements.

When you touch the On field in the V Markers menu, five new fields
appear to the right of the V Markers field: Va On, Va Volts, Vb On, Vb
Volts, and Va to Vb fields. These fields allow you to position the Va
marker and the Vb marker by entering channel numbers and voltage
levels for these markers.

If you turn the voltage markers on while the time markers are also
turned on, the voltage levels that correspond to the time marker
waveform crossings will be deleted from the channel label field. If you
turn the voltage markers off while the time markers are turned on, the
voltage levels that correspond to the time marker waveform crossings
will appear in the channel label field.

When the oscilloscope is in Overlay mode, the Voltage Markers options are not
available.

5-18

«
...
58
59
60
61
62
...
»

Summary of Contents for 16533A

























































































































































Reviews:

No comments