HP 16533A, User Reference, Page: 143 / 152

When Range field, 6–15
When Range values, 6–15
peak-to-peak voltage value, 5–10
positive time, 4–6
Preparation for use, 11–2
preset ECL values, 3–8
Preset field, 3–8
Preset field default setting, 3–8
Preset field values, 3–8
preset TTL values, 3–8
preset values for ECL logic levels, 3–8
preset values for TTL logic levels, 3–8
preshoot, 8–10
probe attenuation factor, 3–7
probe attenuation factor range, 3–7
Probe field, 3–7
Probe field default value, 3–7
R
red line at center of screen, 2–5
trigger point, 4–5
red line, dotted, vertical, 6–4
repetitive mode option, 1–4
repetitive run, 1–4
replacing a channel in the display, 9–9
resolution
delay time, 4–6
rounding of keypad entries, 4–3
run
autoscale, 1–3
mode, 1–3
run field, 1–3
run field pop-up, 1–3
run mode, 1–3
run parameters, 1–3
Run Until Time X- O, Less Than field
resolution, 5–15
Run Until Time X-O field, 5–15 to 5–16
Run Until Time X-O, Greater Than field,
5–16
Run Until Time X-O, In Range field, 5–16
Run Until Time X-O, Less Than field, 5–15
Run Until Time X-O, Not In Range field,
5–16
Run/Stop options, 1–2
running the oscilloscope
using Autoscale, 1–3
S
s/Div field, 4–3 to 4–4
s/Div field default value, 4–4
sample period, 4–8
sample period definition, 4–8
sample period field, 4–8 to 4–13
sample period value display, 4–9
sample period, changing, 4–8
sample rate, 4–8
scrolling, 4–7
Self cal, 11–12
Set on, MANUAL field, 5–17
Show field, 5–9, 5–22
single mode
panning, 4–7
zooming, 4–4
Single Run, 1–3 to 1–4
Slope field, 6–9
Source field, 6–6
Statistics field, 5–14
stop field, 1–4
Stop/Run options, 1–2
sweep speed, 4–3, 4–8
selecting, 4–3
sequence, 4–3
T
Test, 11–8
time base functions, 4–2
time difference
See Tx to To time field
time marker value display, 5–9
To marker
dashed yellow line, 5–8
Trig to O field, 5–8
top and base voltages, 8–7
Trig to O field, 5–8 to 5–9
yellow border, 5–8
Trig to O time value resolution, 5–8
Trig to X default value, 5–7 to 5–8
Trig to X field, 5–7 to 5–8
green border, 5–7
Trig to X time value resolution, 5–7
trigger
default, 6–2
Edge, 6–2
See also Edge trigger
events counter, 6–10
Immediate, 6–2, 6–18
Immediate, use, 6–18
marker, 6–4
marker, at zero delay, 6–7
menu map, 6–2
modes, 6–2
multimodule configuration, 6–2, 6–5, 6–11,
6–18
Pattern, 6–2
Pattern trigger, 6–11
point, 6–4, 6–7
setting the trigger point, 6–7 to 6–8
source, 6–6
trigger level voltage value, 6–7
trigger point range, 6–8
trigger Mode field, 6–2
trigger point, 5–7 to 5–8
trigger point location, 2–5
trigger point, dotted red line, 4–5
trigger qualifier, 6–9
triggering, delay-by-events, 6–9
triggering, events, 6–9
truncation of keypad entries, 3–5
TTL preset values, 3–8
Tx marker, 5–7
Tx to To field, 5–6
U
unsynchronized waveform, 6–8, 6–10
V
V/Div field, 3–5
V/Div field default value, 3–5
Vbase, 8–7
vertical position
See Offset field
vertical sensitivity range, 3–5
vertical sensitivity sequence, 3–5
vertical voltage resolution, 8-bit, 8–7
Vmaximum, 8–7
Vminimum, 8–7
voltage marker value display, 5–22
voltage markers, 5–18
voltage values at Tx and To markers
channel label field, 5–8
Vp_p, 8–7
Vtop, 8–7
Index
Index-3