manualshive.com logo in svg

HP 16533A, User Reference, Page: 111 / 152

Share
Download
HP 16533A User Reference Download Page 111

Waveform Math (Chan+Chan Mode) 

This is a waveform mode that lets you take the signal from one channel input
and add it to the signal from another channel input.  

Waveforms from separate modules cannot be added together when making
an intermodule measurement.

Example

To add the waveform on Input 1 to the waveform on Input 2:

Touch the Channel Mode field on the display, then when the pop-up appears,
touch the Chan+Chan field.

Turn the knob so that the bottom input in the channel label field is
highlighted in white.

Then touch the Action field until Insert is displayed.

Touch the Input 1 label in the Labels field, then touch Input 2 in the Labels
field.

Input 1 and Input 2 waveforms, shown as X1+X2 (where X is the slot letter of
the module) are then displayed in the channel label field.

Now touch the Done key in the pop-up to display the waveform. The display
now shows input 2 added to input 1. The resultant waveform is displayed in
white in the waveform display. 

If T Markers are turned on and V Markers are turned off, voltage values for
this waveform will appear in the channel label field to the left of the
waveform display area.

The Waveform Selection Menu

Channel Mode Field

9-7

Summary of Contents for 16533A

























































































































































Reviews:

No comments