manualshive.com logo in svg

HP 16533A, User Reference, Page: 115 / 152

Share
Download
HP 16533A User Reference Download Page 115

also use the Module field to choose the module that contains the input
channels you wish to display.

Waveform Size Field 

The Waveform Size field accesses a selection menu which contains choices
that scale the displayed waveforms to different sizes.  Use this feature to
increase the number of waveforms in the display or to make viewing better
for just a few. 

Best Fit 

When Best Fit is used, the analyzer picks the largest font, either small,
medium, or large, that allows all waveforms to be displayed. 

Small 

The small font will allow 24 waveforms to be displayed. 

Medium 

The medium font will allow 16 waveforms to be displayed. 

Large 

The large font will allow 8 waveforms to be displayed.

Done Field

When you are finished making all of your selections in the Waveform
Selection pop-up menu, you touch the Done field to enter the selections and
return to the waveform display.  The choices you made while in the
Waveform Selection pop-up will be implemented on the screen.

The Waveform Selection Menu

Waveform Size Field 

9-11

Summary of Contents for 16533A

























































































































































Reviews:

No comments