hopf 8029NTS-V2/GPS Technical Manual Download Page 6

Page: 6 / 121

ABLE OF

ONTENTS

6 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

5.5

Connection LAN Interface ETH0.............................................................................. 27

5.6

Connection Sync Status Optical Coupler ................................................................. 27

Commissioning ........................................................................................................... 28

6.1

General Procedure .................................................................................................. 28

6.2

Switching on the Operating Voltage ......................................................................... 29

6.3

Establish the Network Connection via Web Browser ............................................... 29

6.4

Network Configuration for ETH0 via LAN through

hmc

.......................................... 29

HTTP/HTTPS WebGUI

– Web Browser Configuration Interface ............................... 33

7.1

Quick Configuration ................................................................................................. 33

7.1.1

Requirements ..................................................................................................................... 33

7.1.2

Configuration Steps............................................................................................................ 33

7.2

General

– Introduction ............................................................................................. 34

7.2.1

7.2.2

Navigation via the Web Interface ....................................................................................... 36

7.2.3

Enter or Changing Data ..................................................................................................... 37

7.2.3.1

Changing of Data in 8029NTS (WebGUI: Device) ...................................................................... 37

7.2.3.2

Changing of Data in 8024GPS (WebGUI: Sync Source) ............................................................ 38

7.2.4

Plausibility Check during Input ........................................................................................... 39

7.3

Description of the Tabs ............................................................................................ 40

7.3.1

GENERAL Tab ................................................................................................................... 40

7.3.2

NETWORK Tab .................................................................................................................. 42

7.3.2.1

Host/Nameservice ...................................................................................................................... 42

7.3.2.1.1

Hostname .......................................................................................................................... 42

7.3.2.1.2

Use Manual DNS Entries ................................................................................................... 43

7.3.2.1.3

DNS Server 1 to 3 .............................................................................................................. 43

7.3.2.1.4

Use Manual Gateway Entries ............................................................................................ 43

7.3.2.1.5

Default Gateway IPv4 ........................................................................................................ 43

7.3.2.1.6

Default Gateway IPv6 ........................................................................................................ 43

7.3.2.1.7

Network Interface ETH0..................................................................................................... 44

7.3.2.1.8

Default Hardware Address (MAC) ..................................................................................... 44

7.3.2.1.9

Customer Hardware Address (MAC) ................................................................................. 45

7.3.2.1.10

DHCP ................................................................................................................................ 45

7.3.2.1.11

IPv4 Address ..................................................................................................................... 45

7.3.2.1.12

IPv4 Network Mask ............................................................................................................ 45

7.3.2.1.13

Operation Mode ................................................................................................................. 46

7.3.2.1.14

Maximum Transmission Unit (MTU) .................................................................................. 46

7.3.2.1.15

IPv6 ................................................................................................................................... 46

7.3.2.1.16

DHCP-IPv6 ........................................................................................................................ 46

7.3.2.1.17

IPv6 Address ..................................................................................................................... 47

7.3.2.1.18

IPv6 Subnet Prefix Lengh .................................................................................................. 47

7.3.2.1.19

VLAN (Activation Key necessary) ...................................................................................... 47

7.3.2.2

Routing (Activation Key necessary) ............................................................................................ 48

7.3.2.3

Routing File ................................................................................................................................. 49

7.3.2.4

Management (Management-Protocols

– HTTP, SNMP etc.) ...................................................... 50

7.3.2.4.1

SNMPv2 / SNMPv3 (Activation Key required) ................................................................... 51

7.3.2.5

Time ............................................................................................................................................ 52

7.3.2.5.1

Synchronization Protocols (Time Protocols

– NTP, SNTP etc.) ......................................... 52

7.3.2.5.2

SINEC H1 time datagram (Activation Key necessary) ....................................................... 53

7.3.3

NTP Tab ............................................................................................................................. 54

7.3.3.1

System Info ................................................................................................................................. 55

7.3.3.2

Kernel Info .................................................................................................................................. 55

7.3.3.3

Peers .......................................................................................................................................... 56

7.3.3.4

Server Configuration ................................................................................................................... 57

Summary of Contents for 8029NTS-V2/GPS


























































































































Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands

hopf 8029NTS-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands