hopf 8029NTS-V2/GPS Technical Manual Download Page 108

Page: 108 / 121

ACTORY

EFAULTS OF

IME

ERVER

8029NTS/GPS

108 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

Factory Defaults of Time Server 8029NTS/GPS

This chapter lists the factory default values of the individual components integrated in the Time
Server 8029NTS/GPS.

12.1 Factory Default Values of Module 8029NTS (Device)

The default delivery status of the Time Server 8029NTS/GPS meets the factory default values
when using GPS synchronization sources. In case of DCF77 synchronization (different product
variant) the function

"NTP / General / Sync Source"

is factrory-set to

"DCF77"

on delivery.

Using the board in DCF77 sytems (different product variant) the setting for

NTP / General / Sync Source"

needs to be re-configured to

"DCF77"

after a factory default.

NTP Server Configuration

Setting

WebGUI

Sync Source

DCF77

12.1.1 Network

Host/Name Service

Setting

WebGUI

Hostname

hopf8029nts

Use Manual DNS Entries

Enabled

DNS Server 1 IPv4/IPv6 Address

Blank

---

DNS Server 2 IPv4/IPv6 Address

Blank

---

DNS Server 3 IPv4/IPv6 Address

Blank

---

Use Manual Gateway Entries

Enabled

Default Gateway IPv4 Address

Blank

---

Default Gateway IPv6 Address

Blank

---

Network Interface ETH0

Setting

WebGUI

Use Custom Hardware Address (MAC)

Disabled

Custom Hardware Address (MAC)

Blank

---

DHCP

Disbabled

Disabled

IPv4

192.168.0.1

IPv4-Netmask

255.255.255.0

Operation mode

Auto negotiate

VLAN Interfaces

deaktiviert

disabled

IPv6 Settings

deaktiviert

disabled

Routing

Setting

WebGUI

Use Route File

Disabled

User Defined Routes

Blank

---

Management

Setting

WebGUI

HTTP

Enabled

HTTPS

Disabled

SSH

Enabled

TELNET

Disabled

SNMP

Disabled

System Location

Blank

---

System Contact

Blank

---

Summary of Contents for 8029NTS-V2/GPS


























































































































Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands

hopf 8029NTS-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands