manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 18

 

S

YSTEM 

B

EHAVIOUR

 

 

 

 18 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

4  

System Behaviour 

This  chapter  describes  the  behaviour  of  the  system  in  special  operational  phases  and 
conditions. 

4.1  

Boot Phase 

The boot process of the Time Server 8029NTS/GPS starts after turning on  the system or a 
reset. 

During  the  boot  process  the  Module  8029NTS  boots  its  LINUX  operation  system  and  is 
therefore not available via LAN. 

The  end  of  the  boot  process  is  reached  when  the  green  NTP  LED  is  shining  and  thereby 
indicates that the NTP service on Module 8029NTS has been started and enabled. The boot 
process lasts approx. 1-1.5 minutes. 

4.2  

NTP Adjustment Process (NTP/Stratum/Accuracy) 

NTP is a regulation process. After start of the NTP services, automatically processed during 
booting,  the  Time  Server  8029NTS/GPS  requires  approximately  5-10  minutes  after 
synchronization of the Sync Source (Status "SYNC")  until NTP is set to the high accuracy of 
the Sync Source (here Module 8024GPS) and reaches the optimized operation condition of 

STRATUM = 1

 and 

ACCURACY = High

. 

The  decisive  factors  here  are  accuracy  of  the  synchronization  source  and  the  appropriate 
synchronization condition of the Sync Source. 

4.3  

Reset-(Default) Button 

The Time Server 8029NTS/GPS can be reset by the Reset-(Default) Button behind the front 
panel  of  the  board.  The  Reset-(Default)  Button  is  accessible  with  a  thin  object  through  the 
small drilling in the front panel. 

The button triggers different functions depending on how long it is pressed: 

Duration 

Function 

< 1 sec. 

No action 

1 - 9 sec. 

After releasing a systemwide 

hardware reset

 is triggered  

>= 10 sec. 

After releasing a 

FACTORY DEFAULT

 followd by a 

REBOOT

 is 

triggered after approx. 10 seconds 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands