manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 78

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 78 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

7.3.5.5.1  Select Image Update 

 

 

ATTENTION 

Important note for the identification of the required image update! 

In order to select the correct image update, the 

digit marked red

 of the 

serial number must be checked! 

 
 
 

 

 

 

Required ZIP archive for the Image Update: 

Red marked digit 

= 1 

Red marked digit 

= 4 

hopf8029NTS-V2-

SERI

_GPS_SET_v07xx.zip 

hopf8029NTS-V2-

NAND

_GPS_SET_v07xx.zip 

Content of the ZIP archive 

•

 

8024A_128_v01xx.mot 

•

 

readme_8029NTS-V2-SERI_GPS.txt 

•

 

release-notes_8029NTS-V2-SERI_GPS.html 

•

 

upgrade_8029-

SERI

_gen_rel_v07xx.img 

Content of the ZIP archive 

•

 

8024A_128_v01xx.mot 

•

 

readme_8029NTS-V2-NAND_GPS.txt 

•

 

release-notes_8029NTS-V2-NAND_GPS.html 

•

 

upgrade_8029-

NAND

_gen_rel_v07xx.img 

 

 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands