manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 25

 

I

NSTALLATION

 

 

 

 GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

25 / 121 

hopf 

Elektronik GmbH 

 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

5.3.1.4  Voltage Input / Fuse Protection 

The 100-240V AC connection is made via the pluggable screw terminal L, N and 

. 

Primary Side Fuse Protection 

The device must be installed in accordance with the provisions of EN 60950. There must be a 
suitable isolating device external to the power supply capable of switching the device off. 

The primary side line protection, for example, is suitable for this purpose. 

Further equipment protection is not required because the device is fused internally. 

Recommended External Fuse 

When  connecting  the  Time  Server  8029NTS/GPS  a  suitable  fuse  protection  of  the  power 
supply needs to be observed. 

Accordingly,  the  performance  data  should  be  taken  from  the  nameplate  of  the  device. 
Currently the standard  versions of  the Time Server 8029NTS/GPS are supplied with power 
supplies with power consumption between 6 and 15VA. 

Regarding DC applications a suitable fuse must be connected. 

 

If the internal fuse trips it is highly likely that the device is faulty. In this 
case the equipment should be checked at the factory! 

 

5.3.1.5  Power Supply Specifications 

All  specifications  regarding  the  AC  power  supply  can  be  found  in 

Chapter  12.4  Power 

Supplies

. 

 

5.3.1.6  Power LED 

The green Power LED allows a functional evaluation

 

directly on site at the control cabinet. 

 

LED lights 

Normal power supply operation 

LED off 

No power supply is available or the device is faulty. 

 

5.3.2   DC Power Supply 

 

 

Make sure that the external voltage source is switched off. When 
connecting the power supply, ensure that the polarity and ground 
connection are correct! 

 

 

•

  The power supply cable is connected to the Time Server 

8029NTS/GPS by means of a 2-pole plug connector with 
additional ground connection and interlock: 

 

+V

in

: 

Positive pole (contact 1) 

–V

in

: 

Negative pole (contact 2) 

PE: 

Ground 

 

 

 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands