manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 29

 

C

OMMISSIONING

 

 

 

 GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

29 / 121 

hopf 

Elektronik GmbH 

 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

6.2  

Switching on the Operating Voltage 

The Time  Server  8029NTS/GPS  has  no  own  switch  for  the  power  supply.  The  converter  is 
activated by switching on the external power supply source. 

6.3  

Establish the Network Connection via Web Browser 

 

 

Ensure that the network parameters of the Time Server 8029NTS/GPS 
are configured in accordance with the local network before connecting the 
device to the network. 

 

 

Connecting a network to an incorrectly configured Time Server 
8029NTS/GPS (e.g. duplicate IP address) may cause interference on the 
network.  

 

 

The Time Server 8029NTS/GPS is supplied with a static IP-address 
(equivalent to the factory default setting). 
 

IP-address: 

192.168.0.1 

Network mask:  

255.255.255.0 

Gateway:  

not set 

 

 

 

In case it is not known whether the Time Server 8029NTS/GPS with a 
Factory Default setting causes problems in the network, the basis network 
parameterization should be executed via a "Peer to Peer" network 
connection. 

 

 

Request the required network parameters from your network administrator 
if those are unknown. 

 

The network connection is made via a LAN cable and RJ45 plug (recommended cable type: 
CAT5 or better). 

 

6.4  

Network Configuration for ETH0 via LAN through 

hmc

 

After connecting the system to the power supply and creating the physical network connection 
to LAN interface of the  Time Server 8029NTS/GPS, the device can  be searched for  on the 
network  via  the 

hmc

  (

hopf 

Management  Console

).  Then

 

the  base  LAN  parameters  (IP 

address, netmask and gateway or DHCP) may be adjusted in order to allow accessibility of 
the Time Server 8029NTS/GPS for other systems on the network. 

 

 

The  SEARCH  Function  of  the 

hmc

  - 

Network  Configuration  Assistant 

requires

  for  location  and  recognition  of  the  desired  Time  Server 

8029NTS/GPS the 

hmc

-computer and the Time Server 8029NTS/GPS 

in 

the same SUB Net

.  

 

 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands