manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 76

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 76 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

7.3.5.4  Restarting the Module (Reboot Device / Hardware Reset) 

 

 

The restart concerns the Module 8029NTS only but 

not

 the Sync Source 

(here Module 8024GPS). 

 

Reboot Device

: Restart of the internal Operating System 

 

 

Hardware Reset

: Board Reset including all Hardware components 

 

 

 

All settings 

not

 saved with "

Save

" are lost on reboot (see 

Chapter 7.2.3 

Enter or Changing Data

). 

 

Moreover the 

NTP service

 implemented in the system is restarted. This leads to a renewed 

alignment phase with the loss of the stability and accuracy reached up to this point. 

Log  in  is  carried  out 

as  “Master”  user  in  accordance  with  the  description  in 

Chapter  7.2.1 

LOGIN and LOGOUT as User

.  

Press the "

Reboot now

" button and wait until the restart has been perfomed. 

 

 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands