manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 5

 

T

ABLE OF 

C

ONTENTS

 

 

 

 GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

5 / 121 

hopf 

Elektronik GmbH 

 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

Contents 

Page 

1

 

GPS - NTP Time Server 8029NTS/GPS ........................................................................ 9

 

2

 

System Structure ........................................................................................................ 12

 

2.1

 

Housing ................................................................................................................... 12

 

2.2

 

Power Supply .......................................................................................................... 12

 

2.3

 

Functional Overview of the Front Panel Elements ................................................... 12

 

2.3.1

 

Reset-(Default) Button ....................................................................................................... 12

 

2.3.2

 

NTP Status LEDs (NTP/Stratum/Accuracy) ....................................................................... 13

 

2.3.3

 

USB-Port ............................................................................................................................ 13

 

2.3.4

 

LAN Interface ETH0 ........................................................................................................... 13

 

2.3.4.1

 

MAC-Address for ETH0 .............................................................................................................. 14

 

2.3.5

 

Sync Status Optical Coupler .............................................................................................. 14

 

2.3.6

 

Sync Status LEDs .............................................................................................................. 14

 

2.3.7

 

GPS Antenna Input ............................................................................................................ 15

 

3

 

Function Principle ....................................................................................................... 16

 

3.1

 

Block Diagram ......................................................................................................... 16

 

3.2

 

Function 8029NTS (WebGUI: Device) ..................................................................... 17

 

3.3

 

Function 8024GPS (WebGUI: Sync Source) ........................................................... 17

 

4

 

System Behaviour ....................................................................................................... 18

 

4.1

 

Boot Phase .............................................................................................................. 18

 

4.2

 

NTP Adjustment Process (NTP/Stratum/Accuracy) ................................................. 18

 

4.3

 

Reset-(Default) Button ............................................................................................. 18

 

4.4

 

Firmware Update ..................................................................................................... 19

 

4.4.1

 

Firmware Update 8029NTS (WebGUI: Device) ................................................................. 19

 

4.4.2

 

Firmware Update 8024GPS (WebGUI: Sync Source) ....................................................... 20

 

4.5

 

Activation of Functions (Activation Key) ................................................................... 21

 

5

 

Installation ................................................................................................................... 22

 

5.1

 

Installation/Dismounting of the DIN Rail Housing ..................................................... 22

 

5.1.1

 

Mounting ............................................................................................................................ 22

 

5.1.2

 

Dismounting ....................................................................................................................... 22

 

5.2

 

Protective Earth Conductor (Grounding) .................................................................. 23

 

5.3

 

Power Connection ................................................................................................... 23

 

5.3.1

 

AC Power Supply ............................................................................................................... 23

 

5.3.1.1

 

Safety and Warning Instructions ................................................................................................. 23

 

5.3.1.2

 

Connection to various Power Networks ...................................................................................... 24

 

5.3.1.3

 

Power Cable Connection ............................................................................................................ 24

 

5.3.1.4

 

Voltage Input / Fuse Protection ................................................................................................... 25

 

5.3.1.5

 

Power Supply Specifications ....................................................................................................... 25

 

5.3.1.6

 

Power LED .................................................................................................................................. 25

 

5.3.2

 

DC Power Supply ............................................................................................................... 25

 

5.3.2.1

 

Power Supply Unit Specifications ............................................................................................... 26

 

5.3.2.2

 

Fuse Protection ........................................................................................................................... 26

 

5.4

 

Connection GPS Antenna System ........................................................................... 26

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands