hopf 8029NTS-V2/GPS Technical Manual Download Page 12

Page: 12 / 121

YSTEM

TRUCTURE

12 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

System Structure

Views of the Timer Server 8029NTS/GPS with AC and DC power supply.

2.1

Housing

The Time Server 8029NTS/GPS is built into a closed aluminium profile housing for DIN Rail
mounting according to DIN EN 60715 TH35.

2.2

Power Supply

Currently the following types of power supplies are available:

•

AC/DC wide range power supply 100-240V AC / 110-250V DC

Type: AC-M05-D

•

DC power supply 18-36V DC (nominal voltage 24V DC)

Type: DC24-M15-D

•

DC power supply 36-76 VDC (nominal voltage 48V DC)

Type: DC48-M15-D

2.3

Functional Overview of the Front Panel Elements

This chapter describes the individual front panel elements and their functions.

2.3.1 Reset-(Default) Button

The Reset-(Default) Button is accessible with a thin object through the
small drilling in the front panel next to the "Reset" inscription" (see

Chapter 4.3 Reset-(Default) Button

Summary of Contents for 8029NTS-V2/GPS


























































































































Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands

hopf 8029NTS-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands