hopf 8029NTS-V2/GPS Technical Manual Download Page 14

Page: 14 / 121

YSTEM

TRUCTURE

14 / 121

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

2.3.4.1 MAC-Address for ETH0

Each LAN interface is clearly identifiable on the Ethermet via a unique MAC Address
(hardware address).

The MAC address given for the LAN interface ETH0 can be read in WebGUI of the appropriate
board or be evaluated via the

hmc

Network Configuration Assisant.

The MAC address is

uniquely assigned for each LAN interface by the company

hopf

Elektronik GmbH.

The factory set MAC address for the Time Server 8029NTS/GPS is stated
on a sticker laterally positioned on the exterior of the housing of the device.

hopf

Elektronik GmbH MAC addresses begin with

00:03:C7

:xx:xx:xx.

2.3.5 Sync Status Optical Coupler

Sync Status Optical Coupler

3-pole pluggable Connector

Pin

Signal

Collector

n.c.

Emitter

2.3.6 Sync Status LEDs

Sync Status LEDs

LED

Meaning

Status LED red

Status LED green

The Status LEDs on the front panel signal the current (synchronization) status of the Sync
Source (here Module 8024GPS). The meanings of the LEDs are as follows:

LED RD
- Red

LED GN
- Green

Status

STATUS

Code

Off

Sync

(radio-synchronous) with quartz regulation

SYNC

Off

Flashes

Sync

(radio-synchronous) - SyncOFF timer running

SYOF

Flashes

Sync

(radio-synchronous) - simulation mode

SYSI

Flashes

Quarz

- SyncON timer running

QUON

Quarz

- time was set via synchronization source

QUEX

Flashes

Quarz

- time set manually or after reset

QUSE

Off

No valid time

INVA

Off

No operating voltage / faulty

---

3Hz

Off

General Module Error (PCID)

INVA

3Hz

Invert

3Hz

User-Settings missing
(Difference time / ST-WT changeover)

INVA

Summary of Contents for 8029NTS-V2/GPS


























































































































Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands

hopf 8029NTS-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands