manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 23

 

I

NSTALLATION

 

 

 

 GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

23 / 121 

hopf 

Elektronik GmbH 

 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

5.2  

Protective Earth Conductor (Grounding) 

Grounding of the Time Server 8029NTS/GPS is achieved via the PE line of the power supply 
wiring. 

5.3  

Power Connection 

Depending on the version of the appliance an AC or DC power feeding is available. 

5.3.1   AC Power Supply 

The standard AC power supply unit of the Time Server 8029NTS/GPS is described hereunder. 
However,  the  connection  data  on  the  nameplate  of  the  respective  device  are  always 
applicable. 

Pay attention to the following when connecting the power supply: 

•

 

Correct voltage type (AC or DC), 

•

 

Voltage amount 

 

The power cable is connected via a 3pole pluggable screw terminal with housing. 

N

L

 

 

 

Connecting the incorrect voltage can damage the Time Server 8029NTS/GPS. 

 
 

5.3.1.1  Safety and Warning Instructions 

Please read these instructions thoroughly to facilitate safe operation of the device and to use 
all of its functions! 

 

Warning:

 Never work on live equipment! Danger to life! 

 

The Time Server 8029NTS/GPS is a built-in device. Installation and commissioning may only 
be  carried  out  by  suitable  specialist  personnel.  In  doing  so  the  respective  country-specific 
regulations (e.g. VDE, DIN) must be observed. 

In particular, before commissioning please ensure that  

•

 

The power connection has been installed correctly and there is guaranteed protection 
against electric shock! 

•

 

The ground wire is connected! 

•

 

All power cables are correctly fused and sized! 

•

 

All output lines are sized in accordance with the max. output current of the device or 
are specially fused! 

•

 

Sufficient convection is guaranteed! 

 

The device contains components carrying life-threatening voltage and a high amount of stored 
energy! 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands