manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 30

 

C

OMMISSIONING

 

 

 

 30 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

The  base  LAN  parameters  can  be  set  via  the 

hmc

  integrated 

Network  Configuration 

Assistant

. 

 

 

 

After a successful start of the 

hmc 

Network Configuration Assistant

 and completed search 

of the 

hopf 

LAN devices, the configuration of the base LAN parameters can be done.  

 

The Time Server 8029NTS/GPS is stated as 

8029NTS in the

 

Device List. 

The determination of different Time Server 8029NTS/GPS (or other products variants) is made 
via 

Hardware Address

 (MAC Address). 

 

 

The factory set MAC address for the Time Server 8029NTS/GPS is stated 
on a sticker laterally positioned on the exterior of the housing of the device. 

 

 

 

 

 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands