hopf 8029NTS-V2/GPS Technical Manual Download Page 41

Page: 41 / 121

HTTP/HTTPS

GUI

–

ROWSER

ONFIGURATION

NTERFACE

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00

41 / 121

hopf

Elektronik GmbH

Nottebohmstr. 41

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

Sync Source Status

Display of the actual status of synchronization of the Sync Source (here Module 8024GPS)
with these possible values:

SYNC

Time synchr Quartz regulation started/running

SYOF

Time synchr SyncOFF running

SYSI

Time synchronized as simulation mode
(without actual GPS reception)

QUON

Quartz/Crystal time + SyncON running

QUEX

Quartz/Crystal time (in freewheel after synchronization
failure



Board was already synchronized)

QUSE

Quartz/Crystal time after reset or manual setting

INVA

Invalid time

Login

The login box is described in

Chapter 7.2.1 LOGIN and LOGOUT as User

System Overview

This table gives a direct overview of th

e Time Server’s 8028NTS/GPS current operating states.

WebGUI

Description

Sync Source OK

When active (RED) there is a Sync Souce
failure. For details please go to

GPS SYNC

SOURCE

tab

- Module Errors.

Announcement leap second inactive

When active (ORANGE) there is an
announcement for a leap-second.

Announcement STD



DST inactive

When active (ORANGE) there is an
announcement for a summer / winter time
change-over.

NTP is running

The NTP process on Module 8029NTS is
running

NTP has stratum 1

Shows the appropriate stratum the NTP
process works with.

NTP Accuracy is High

Shows the appropriate accuracy the NTP
process works with.

Announcements

The display fields LEAP SECOND and STD



DST announce a corrosponding event to the

next hour (insertion of a leap-second or rather switchover of summer/winter time).

Summary of Contents for 8029NTS-V2/GPS


























































































































Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands

hopf 8029NTS-V2/GPS, Technical Manual

Search results

Summary of Contents for 8029NTS-V2/GPS

Reviews:

Brands by name

Popular brands