manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 24

 

I

NSTALLATION

 

 

 

 24 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

5.3.1.2  Connection to various Power Networks 

 

 

 

 

5.3.1.3  Power Cable Connection 

The power cable is connected via a 3pole pluggable screw terminal. The following cable cross-
sections can be connected to the input plug: 

 

 

Fixed 

[mm

2

] 

Flexible 

[mm

2

] 

AWG 

Starting moment 

[Nm] 

L, N, 

 

 

0.2-2.5 

0.2-2.5 

24-12 

0.5 

– 0.6 

 

 

For a reliable and secure contact: 

Strip the insulation by 8 mm! 

 

 

 

The connector must always be mounted using the housing and strain 
relief fitting provided. 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands