manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 46

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 46 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

7.3.2.1.13 Operation Mode 

The network device usually adjusts the data stream and duplex mode to the device to which it 
is connected (e.g. HUB, SWITCH) automatically. If the network device requires a certain speed 
or  duplex  mode,  this  can  be  configured  via  the  web  interface.  The  value  should  only  be 
changed in special cases. The automatic setting is normally used.  

 

 

 

 

In  individual  cases  an  enabled  "Auto  negotiate"  might  lead  to  problems 
between the network components and the adjustment process fails.  

In  such  cases  it  is  recommended  to  set  the  network  speed  of  the  Time 
Server 8029NTS/GPS 

and

 the connected network components manually to 

the same value. 

 

7.3.2.1.14 Maximum Transmission Unit (MTU) 

The Maximum Transmission Unit describes the maximum size of a data packet of a protocol 
of the network layer (layer 3 of OSI model), measured in octets which can be transferred into 
the frame of a net of the security layer (layer 2 of OSI model) without fragmentation.   

The Time Server 8029NTS is going to be delivered with default setting 1356. 

7.3.2.1.15 IPv6 

The Time Server 8030NTS/GPS can also be operated in an IPv6 network. 

To enable IPv6, 

Use IPv6 Settings

 must be set to 

enable

. 

IPv6  addresses  are  128  bits  long  and  they  are  recorded  in  eight  4-character  hexadecimal 
blocks. For example: 

2001:0db8:0000:08d3:1319:8a2e:0370:7344

 

Leading zeroes in a 4-character hexadecimal block can be omitted. For the above example, 
this results in the notation: 

2001:db8:0:8d3:1319:8a2e:370:7344

 

In addition, 

once

 per IPv6 address a consecutive sequence of blocks containing all zeros may 

be omitted. But this must be recorded with two consecutive colons. For the above example, 
this gives the notation: 

2001:db8::8d3:1319:8a2e:370:7344

 

Another example: 

2001:0:0:0:1319:8a2e:0:7344

 may be represented  

as  

2001::1319:8a2e:0:7344  

or  

2001:0:0:0:1319:8a2e::7344 

7.3.2.1.16 DHCP-IPv6 

If DHCP is to be used, this function is activated with 

enabled

. 

 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands