manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 56

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 56 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

7.3.3.3  Peers  

The “Peers summary” is used to track the performance of the configured NTP server/driver 
and the NTP algorithm itself. 

The  information  displayed  is  identical  with  the  information  available  via  NTPQ  or  NTPDC 
programes. 

Each NTP server/driver that has been set up in the NTP server configuration is displayed in 
the peer information. 

The connection status  is displayed  in the reachability  column (not reachable, bad, medium, 
and reachable). 

 

 

The first line displays the 

hopf 

- refclock ntp driver 

that gets the time information directly 

from the Sync Source. 

A  short  explanation  and  definition  of  the  displayed  values  can  be  found  in 

Chapter

 

13.5 

Accuracy & NTP Basic Principles

. 

The character in the first column on the left presents the current status of the NTP association 
in the NTP selection algorithm. A list and description of possible characters can be found in 
the Glossary (see 

Chapter 13.2 Tally Codes (NTP-specific)

). 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands