manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 34

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 34 / 121 

GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

hopf 

Elektronik GmbH 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected]

 

7.2  

General 

– Introduction 

The Time Server 8029NTS/GPS should be accessible to a web browser if it has been set up 
correctly. Enter the IP address - as set up in the Time Server 8029NTS/GPS earlier - or the 
DNS  name  on  the  address  line  <

http://xxx.xxx.xxx.xxx

>  and  the  following  screen  should 

appear. 

When using IPv6, it is mandatory to enclose the IPv6 address with [ ]  
e.g..: 

http://[2001:0db8:85a3:08d3::0370:7344]/

 

 

 

The complete configuration can only be completed via the modules 
WebGUI!  

 

 

 

 

 

The WebGUI was developed for multi-user read access but not for multi-
user write access. It is the responsibility of the user to pay attention to this 
issue. 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands