manualshive.com logo in svg

hopf 8029NTS-V2/GPS, Technical Manual

Share
Download
hopf 8029NTS-V2/GPS Technical Manual Download Page 55

 

HTTP/HTTPS

 

W

EB

GUI

 

–

 

W

EB 

B

ROWSER 

C

ONFIGURATION 

I

NTERFACE

 

 

 

 GPS - NTP Time Server with LAN Interface 8029NTS-V2/GPS - V08.00 

55 / 121 

hopf 

Elektronik GmbH 

 

Nottebohmstr. 41 

• D-58511 Lüdenscheid • Tel.: +49 (0)2351 9386-86 • Fax: +49 (0)2351 9386-93 • Internet: http://www.hopf.com • E-Mail: [email protected] 

7.3.3.1  System Info 

In  the  window  "System  Info"  the  current  NTP  values  of  the  NTP  service  running  on  the 
embedded  Linux  of  the  Time  Server  8029NTS/GPS  are  indicated.  In  addition  to  the  NTP 
calculated  values for  root  delay, root  dispersion, jitter, and stability the stratum value  of the 
Time Server 8029NTS/GPS, the status to the leap second, and the current system peer are 
also found here.  

The NTP version used adjusts the leap second correctly. 

The Time Server 8029NTS/GPS works as NTP Server with stratum 1 and belongs to the best 
available class of NTP server, as it has a reference clock with direct access. 

 

7.3.3.2  Kernel Info  

The  “Kernel  Info”  overview  shows  the  current  error  values  of  the  internal  embedded  Linux 
clock. Both values are internally updated every second. 

 

 

This  screenshot  shows  a  maximum  kernel  clock  error  of  3.000  msec  (milliseconds).  The 
estimated error value is 14 

μs (microseconds). 

The  values  indicated  here  are  based  on  the  calculation  of  the  NTP  service  and  have  no 
significance for the accuracy of the Sync Source (here Module 8024GPS). 

 

Summary of Contents for 8029NTS-V2/GPS


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands