Honeywell UDC 2300, Product Manual

Page: 174 / 185

Index
164 UDC2300 Controller Product Manual 12/00
Ramp/soak profile example, 77
Rate 2 in Minutes, 27
Rate Down, 29
RATE DOWN VALUE, 133
Rate in Minutes, 27
RATE TIME, 148
Rate Up, 29
RATE UP VALUE, 133
RATE2 TIME, 148
Ratio on Input 1, 34
Ratio on Input 2, 35
Recycle number, 75
RECYCLES, 149
Relative Humidity, 4
Relay Cycle Time Increment, 32
RELAY CYCLE TIME INCREMENT, 149
Remote Setpoint Source, 36
REMOTE SETPOINT SOURCE, 150
RESET - INTEGRAL TIME, 136
Reset in minutes/repeat, 27
Reset in repeats/minute, 27
Reset Program to Beginning, 76
Reset Program to the Beginning, 30
RESET PROGRAMMING TO BEGINNING, 156
Reset Units, 37
RESET UNITS, 142
RESET2 - INTEGRAL TIME, 136
Response Delay, 39
RESPONSE DELAY, 157
Restore Factory Calibration, 93
RTD Inputs, 88
Run/Hold key, 48
RUN/HOLD key, 71
Run/Hold Key Lockout, 28
RUN/HOLD KEY LOCKOUT, 150
Run/Monitor the program, 80
S
Security Code, 28, 46
SECURITY CODE, 151
SEGMENT DURATION, 152
SEGMENT RAMP, 151
Segment Ramp or Rate Time, 30
SEGMENT SETPOINT, 151
Segment Soak Duration, 30
Segment Soak Setpoint Value, 30
Set Point Select function key, 48
Set Up Group, 24
Set Up groups, 23
Set Up Wiring Procedure for Auxiliary Output, 98
Setpoint High Limit, 36
SETPOINT HIGH LIMIT, 153
Setpoint Low Limit, 36
SETPOINT LOW LIMIT, 153
Setpoint Ramp, 29, 72
Setpoint Ramp Final Setpoint, 29
SETPOINT RAMP/SOAK PROGRAM, 154
Setpoint Ramp/Soak Programming, 29, 74
Setpoint Rate, 29, 72
SETPOINT RATE, 154
Setpoint Rate/Ramp/Program Operation, 71
Setpoint Select Function Lockout, 28
SETPOINT SELECT FUNCTION LOCKOUT, 155
Setpoint Tracking, 36
SETPOINT TRACKING, 155
Setpoints, 58
SHED MODE, 152
Shed Output Mode, 40
Shed Setpoint Recall, 40
SHED SETPOINT RECALL, 152
Shed Time, 39
SHED TIME, 152
Shock hazard warning, 108
SINGLE DISPLAY DEFAULT, 133
Single Display Functionality, 54
Single Display Parameters, 55
SINGLE SETPOINT RAMP, 154
SINGLE SETPOINT RAMP FINAL SETPOINT,
134
Single Setpoint Ramp Time, 29
SINGLE SETPOINT RAMP TIME, 156
Soak segments, 75
software version number, 103
Solid State Relay Output, 15
SP RAMP, 29
SP Ramp Set Up Group, 29
Specifications, 4
SPPROG, 29
SPRATE, 29
Start Segment, 29
START SEGMENT, 156
Start segment number, 75
Start Segment Number, 29
start up, 21
Start Up Procedure for Operation, 56
Station Address, 39
STATION ADDRESS, 127
Status Tests, 104
Suppression Devices, 11
Switch between two sets via keyboard, 65
Switching between setpoints, 59
T
Temperature Units, 33
TEMPERATURE UNITS, 157
Test Failures, 21, 104
Thermocouple Inputs Using a Thermocouple Source,
87