Honeywell AlarmNet 7810iR-ent Installation And Setup Manual Download Page 83

Page: 83 / 104

Section 6: Message Formats

6-17

454

Failed to Close

Trouble-Fail to Close (Restore not applicable)

455

Auto-Arm Failed

Trouble-Auto Arm Failed (Restore not applicable)

456

Partial Arm

Closing-Partial arm-User #

457

Exit Error (User)

Closing-Exit Error-User #

458

User on Premises

Opening-User on Prem. – User #

459

Recent Close

Trouble-Recent Close – User # (Restore not appl)

461

Wrong Code Entry

Access – Wrong Code entry (Restore not applicable)

462

Legal Code Entry

Access-Legal Code entry – user # (Restore not appl)

463

Re-arm after Alarm

Status-Re Arm After Alarm-User # (Restore not appl)

464

Auto Arm Time Extended

Status-Auto Arm Time Ext. – User # (Restore not appl)

465

Panic Alarm Reset

Status-PA Reset (Restore not applicable)

Remote Access

411

Callback Requested

Remote-Callback Requested (No Restore) Enabled

with O/C reports

412

Success-Download/access

Remote-Successful Access (Restore Not Applicable)

413

Unsuccessful Access

Remote-Unsuccessful Access (Restore Not Applicable)

414

System Shutdown

Remote-System Shutdown

415

Dialer Shutdown

Remote-Dialer Shutdown

416

Successful Upload

Remote-Successful Upload (Restore Not Applicable)

Access Control

421

Access Denied

Access-Access Denied-User # (Restore Not

Applicable)

422

Access Report by User

Access-Access Gained –User# (Restore Not

Applicable)

423

Forced Access

Panic-Forced Access-#

424

Egress Denied

Access-Egress Denied (Restore Not Applicable)

425

Egress Granted

Access-Egress Granted-# (Restore Not Applicable)

426

Access Door Propped Open

Access-Door Propped Open-#

427

Access Point DSM Trouble

Access-ACS Point DSM Trbl.-#

428

Access Point RTE Trouble

Access-ACS Point RTE Trbl.-#

429

Access Program Mode Entry

Access-ACS Prog. Entry-User # (Restore Not

Applicable)

430

Access Program Mode Exit

Access-ACS Prog. Exit-User # (Restore Not

Applicable)

431

Access Threat Level Change Access-ACS Threat Level Chg.

432

Access Relay/Trigger Fail

Access-ACS Relay/Trig. Fail-#

433

Access RTE Shunt

Access-ACS RTE Shunt-#

434

Access DSM Shunt

Access-ACS DSM Shunt-#

System Disables

501

Access Reader Disable

Disable-Access Rdr. Disable-#

Summary of Contents for AlarmNet 7810iR-ent









































































































Search results

Summary of Contents for AlarmNet 7810iR-ent

Reviews:

Brands by name

Popular brands

Honeywell AlarmNet 7810iR-ent, Installation And Setup Manual

Search results

Summary of Contents for AlarmNet 7810iR-ent

Reviews:

Brands by name

Popular brands