manualshive.com logo in svg

Honeywell AlarmNet 7810iR-ent, Installation And Setup Manual

Share
Download
Honeywell AlarmNet 7810iR-ent Installation And Setup Manual Download Page 43

Section 4: Programming 

 

4-21 

Action 

Screen Display 

9.  If Synchronize the (back up) Secondary 

CS is touched then a confirmation window 

is displayed. 
Touch OK to continue.  

   

 
Touch Cancel to cancel the operation. 

 

 

 

 

10.  Synchronization successful message 

is displayed when the subscriber database 

synchronization is successfully completed. 

NOTE:

 Synchronization is not available 

from the Secondary Central Station. 

 

 

 

 
IMPORTANT: The secondary 7810iR-ent does not keep track of when the last time a 

subscriber was heard from or the current communications status of subscriber.  Account 

status of a subscriber cannot be changed from the secondary 7810iR-ent.  Subscriber 

network services cannot be enabled or disabled from the secondary 7810iR-ent. 
 

Summary of Contents for AlarmNet 7810iR-ent









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands