manualshive.com logo in svg

Honeywell AlarmNet 7810iR-ent, Installation And Setup Manual

Share
Download
Honeywell AlarmNet 7810iR-ent Installation And Setup Manual Download Page 36

7810iR-ent Internet/Intranet Alarm Receiver Installation and Setup Guide 
 

4-14 

Action 

Screen Display 

5.  Touch the 

Install 7810iR

 button.

 

 

 

 

 

 

6.  Backup receiver can be configured as 

shown: 

Configure all parameters: 

•

  Select role of 

This 7810iR

 as 

Secondar

y 

•

  Select role of 

Other 7810iR

 as 

Primary 

  

•

  Enter IP address of primary 

receiver 

•

  Listening Port is used in Private 

LAN mode only.  This port is 

programmed into the 7845i-ent.  

Under normal circumstances there 

is no need to change this port. 

•

  Compass Connect Port field is 

used in Private LAN mode only.  

Change in value of this port must 

be coordinated with changes of IP 

ports of other pieces of software 

working in Compass connect. 

•

  Select 

Supervise Subs

 if you 

want the secondary Central 

Station to have the same 

supervision interval as the primary 

Central Station.  If selected, the 

communication module secondary 

CS IP supervision must be 

programmed for “Full Rate”. 

 
 
 

 

If the 7810iR-ent is programmed 

for Supervise Subs, older 7845i-

ent units reporting to it without 

the Full Rate option will not 

recognize Full Rate supervision, 

which will result in a comm. 

failure to the second CS. 

Therefore it is recommended you 

do not select 

Supervise Subs

 if 

any older 7845i-ent units are 

reporting to this receiver. 

  

              

 

Summary of Contents for AlarmNet 7810iR-ent









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands