manualshive.com logo in svg

Honeywell AlarmNet 7810iR-ent, Installation And Setup Manual

Share
Download
Honeywell AlarmNet 7810iR-ent Installation And Setup Manual Download Page 77

Section 6: Message Formats 

 

6-11 

Message 

Definition 

Applies to 

wired to the alarm control so that a si

gnal is sent to the 

radio when the alarm is 

Disarmed (Opening) or Armed 

(Closing).   
Note regarding the 7620ULF: Due to the fact that the 

7620ULF is not a fire alarm control, supervisory faults 

from the fire control panel may be used to trigger one or 

more of the eight channels on the 7620ULF, and thus will 

be reported as alarms.  The central station should be 

aware of which of the eight channels are actually 

reporting supervisory conditions so alarm reports for 

these channels can be responded to correctly. 

cccc 5555 5551 7 

AC Loss 

7620ULF 

only 

cccc 5555 5553 7 

AC Loss Restore 

7620ULF 

only 

RCVB 5155 5555 7  While “Fail to manual” in LRR Line Card or 685 - 

Automation – Auto button unchecked 

7810iR-ent 

RCVB 5551 5555 7  While “Fail to manual” in LRR Line Card or 685 - 

Automation – Auto button checked 

7810iR-ent 

Status Channel = 8 (Alarm with low battery (older 7620 radio only) 

NOTES: Each channel that displays these message types corresponds to a particular type of 

event.  Because there are eight channels, it is possible for multiple events to be reported in 

multiple channels in only one message.  
(Example: “cccc 1553 5155 8”

 

indicates an alarm on zone 1, a restore on zone 4 and a low 

battery.) 

Message 

Definition 

Applies to 

cccc 5555 5555 8 

Low Battery Massage   

7620 or 

7620ULF 

only 

cccc zzzz zzzz 8 

Low Battery with Reported Alarms  
Alarm messages are identical to those reported when the 

status channel is a “7”.  The “8” only indicates that a low 

battery condition is also present.  (Please refer to the 

description of alarm messages for status channel of “7”.) 
For these radios, the low battery message will be 

repeated when other trouble conditions are reported 

(where the status channel = ‘6’).  The low battery 

message will be sent directly following the trouble 

message. 
In addition, the low battery message will also be sent 

when any alarm or restore is reported.   
These radios do not have a specific Low Battery Restore 

message.  After a low battery condition is received, a 

Low Battery Restore is implied when the next alarm or 

Open/Close message is received with a ‘7’ in the ninth 

channel rather than an ‘8’. 

7620 or 

7620ULF 

only 

 

 

Summary of Contents for AlarmNet 7810iR-ent









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands