Hitachi WJ200-004M Quick Reference Manual Download Page 76

Page: 76 / 77

“P” Function

Defaults

Func.

Code

Name

Description

Run

Mode

Edit Initial data Units

p041

Speed / Torque control
switching time

Set range is 0 to 1000 ms

P044

Communication watchdog

timer

(for option)

Set range is 0.00 to 99.99s

1.00

P045

Inverter

action on

communication error
(for option)

00 (tripping),
01 (tripping after decelerating and
stopping the motor),
02 (ignoring errors),
03 (stopping the motor after
free-running),
04 (decelerating and stopping
the motor)

−

P046

DeviceNet polled I/O:
Output instance number

0-20

−

P048

Inverter action on
communication idle mode

00 (tripping),
01 (tripping after decelerating and

stopping the motor),

02 (ignoring errors),
03 (stopping the motor after

free-running),

04 (decelerating and stopping the

motor)

−

P049

Motor poles setting for RPM

0/2/4/6/8/10/12/14/16/18/20/22/24/26
/28/
30/32/34/36/38/40/42/44/46/48

−

p055

Pulse train input frequency
scale setting

Sets the pulse numbers at max.
frequency, set range is 1.0~32.0 kHz

25.0

kHz

p056

Pulse train input frequency
filter time constant setting

Set range is 0.01~2.00 sec.

0.10

sec.

p057

Pulse train input bias setting

Set range is –100~100 %

p058

Limitation of the pulse train
input setting

Set range is 0~100 %

100.

P060

Multistage position 0

−

P061

Multistage position 1

−

P062

Multistage position 2

−

P063

Multistage position 3

−

P064

Multistage position 4

−

P065

Multistage position 5

−

P066

Multistage position 6

−

P067

Multistage position 7

P073 to P072

(Displayed higher 4-digits only)

−

P068

Homing mode selection

…Low speed mode

…High speed mode

−

P069

Homing direction

…Forward rotation side

…Reverse rotation side

−

P070

Low speed homing freq.

0 to 10Hz

5.00 Hz

P071

High speed homing freq.

0 to 400Hz

5.00 Hz

P072

Position range (Forward)

0 to +268435455(Higher 4-digits
displayed)

+268435

455

−

P073

Position range (Reverse)

–268435455 to 0(Higher 4-digits
displayed)

-2684354

−

Summary of Contents for WJ200-004M














































































Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands

Hitachi WJ200-004M, Quick Reference Manual

Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands