Hitachi WJ200-004M Quick Reference Manual Download Page 2

Page: 2 / 77

Cautions, Warnings and Instructions

xii

Warnings and Cautions for Troubleshooting and Maintenance

The warnings and instructions in this section summarize the procedures necessary to ensure an
inverter installation complies with Underwriters Laboratories

guidelines.

WARNING:

Use 60/75

C Cu wire only.

WARNING:

Suitable for use on a circuit capable of delivering not more than 100,000 rms

Symmetrical Amperes, 120V maximum.

WARNING:

When protected by J class Fuses, or when Protected by Type E

Combination Motor

Controller

Having An Interrupting Rating Not Less Than 100,000 rms Symmetrical Amperes, 120

Volts Maximum.

WARNING:

Install device in pollution degree 2 environment.

WARNING:

Maximum Surrounding Air Temperature 45

C (004M),50

C(007M).

WARNING:

Solid state motor overload protection is provided in each model

WARNING:

Integral solid state short circuit protection does not provide branch circuit protection.

Branch circuit protection must be provided in accordance with the National Electric Code and any
additional local codes

Summary of Contents for WJ200-004M














































































Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands

Hitachi WJ200-004M, Quick Reference Manual

Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands