Hitachi WJ200-004M Quick Reference Manual Download Page 64

Page: 64 / 77

“C” Function

Defaults

Func.

Code

Name

Description

Run

Mode

Edit

Initial data

Units

C102

Reset selection

Determines response to Reset
input [RS].
Four option codes:

…

Cancel trip state at input signal

ON transition, stops inverter if
in Run Mode

…

Cancel trip state at signal OFF

transition, stops inverter if in

Run Mode

…

Cancel trip state at input ON

transition, no effect if in

Run Mode

…

Clear the memories

only related to trip status

−

C103

Restart mode after reset

Determines the restart mode after
reset is given, three option codes:

…

Start with 0 Hz

…

Start with freq. matching

…

Start with active freq. matching

−

C104

UP/DWN clear mode

Freq. set value when UDC signal is
given to the input terminal, two
option codes:

…

0 Hz

…

Original setting (in the

EEPROM memory at power on)

−

C105

EO gain adjustment

Set range is 50 to 200%

100. %

C106

AM gain adjustment

Set range is 50 to 200%

100. %

C109

AM bias adjustment

Set range is 0 to 100%

0. %

C111

Overload warning level 2

Sets the overload warning signal
level between 0% and 200% (from
0 to two time the rated current of
the inverter)

Rated current

x 1.15

C130

Output [11] on delay

0.0 sec.

C131

Output [11] off delay

Set range is 0.0 to 100.0 sec.

0.0 sec.

C132

Output [12] on delay

0.0 sec.

C133

Output [12] off delay

Set range is 0.0 to 100.0 sec.

0.0 sec.

C140

Relay output on delay

0.0 sec.

C141

Relay output off delay

Set range is 0.0 to 100.0 sec.

0.0 sec.

C142

Logic output 1 operand A

−

C143

Logic output 1 operand B

All the programmable functions
available for logic (discrete) outputs
except LOG1 to LOG3, OPO, no

−

C144

Logic output 1 operator

Applies a logic function to calculate
[LOG] output state,
Three options:

…

[LOG] = A AND B

…

[LOG] = A OR B

…

[LOG] = A XOR B

−

C145

Logic output 2 operand A

−

C146

Logic output 2 operand B

All the programmable functions
available for logic (discrete) outputs
except LOG1 to LOG3, OPO, no

−

Summary of Contents for WJ200-004M














































































Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands

Hitachi WJ200-004M, Quick Reference Manual

Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands