Hitachi WJ200-004M Quick Reference Manual Download Page 11

Page: 11 / 77

Using the Front Panel Keypad

Please take a moment to familiarize yourself with the keypad layout shown in the figure
below. The display is used in programming the inverter’s parameters, as well as monitoring
specific parameter values during operation.

Key and Indicator Legend

Items

Contents

(1) POWER LED

Turns ON (Green) while the inverter is powered up.

(2) ALARM LED

Turns ON (Red) when the inverter trips.

(3) Program LED

Turns ON (Green) when the display shows changeable parameter.

Blinks when there is a mismatch in setting.

(4) RUN LED

Turns ON (Green) when the inverter is driving the motor.

(5) Monitor LED [Hz]

Turns ON (Green) when the displayed data is frequency related.

(6) Monitor LED [A]

Turns ON (Green) when the displayed data is current related.

(7) Run command LED

Turns ON (Green) when the RUN command source is set to the operator. (Run key is
effective.)

(8) 7-seg LED

Shows each parameter, monitors etc.

(9) RUN key

Makes inverter run.

(10) STOP/RESET key

Makes inverter stop, according to parameter setup.

Reset the inverter when it is in trip situation

(11) ESC key

Go to the top of next function group, when a function mode is shown

Cancel the setting and return to the function code, when a data is shown

Moves the cursor to a digit left, when it is in digit-to-digit setting mode

Pressing for 1 second leads to display data of

d001

, regardless of current display.

(12) Up key
(13) Down key

Increase or decrease the data.

Pressing the both keys at the same time gives you the digit-to-digit edit.

(14) SET key

Go to the data display mode when a function code is shown

Stores the data and go back to show the function code, when data is shown.

Moves the cursor to a digit right, when it is in digit-to-digit display mode

(15) USB connector

Connect USB connector (mini-B) for using PC communication

(16) RJ45 connector

Connect RJ45 jack for remote operator

RUN

ESC

STOP/

RESET

SET

8888

RUN

PWR

ALM

PRG

(1) POWER LED

(2) ALARM LED

(8) 7-seg LED

(4) RUN LED

(10) STOP/RESET key

(15) USB connector

(3) Program LED

(16) RJ45 connector

(14) SET key

(13) Down key

(12) Up key

(11) ESC key

(9) RUN key

(7) Run command LED

(5) Monitor LED [Hz]

(6) Monitor LED [A]

Summary of Contents for WJ200-004M














































































Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands

Hitachi WJ200-004M, Quick Reference Manual

Search results

Summary of Contents for WJ200-004M

Reviews:

Related manuals for WJ200-004M

Brands by name

Popular brands