Grizzly Pro Video r-THREE Operating Instructions Manual Download Page 54

Page: 54 / 64

r3a-x2.0

♦

The Pan/Tilt Joystick when pushed down, tilts up
and I want it to tilt down :

See the Advanced Options SYS MODE

System

Configuration

which will allow you to switch

the up/down direction for joystick tilt.

♦

The Pan and/or Tilt is not working :

Check that the amber PAN LIMIT or TILT
LIMIT lights are not on. If they are, you have
reached the limit of the

r-THREE

Pan/Tilt

Head.

Check the cabling.

♦

The Preview or Program Monitor is black even
though the camera is powered on and the PWR
Button has been pressed :

Check that the desired camera has been
selected on the Preview Buttons and the PWR
Button has been pressed.

Check that the lens cap is off on the camera.

Check the cabling.

♦

Time Code MODE shows

PANA

for my LANC

camera.

Check that the switch on the

r-THREE

Pan/Tilt

Head is set to LANC when a LANC camera is
attached.

Summary of Contents for r-THREE

































































Search results

Summary of Contents for r-THREE

Reviews:

Related manuals for r-THREE

Brands by name

Popular brands

Grizzly Pro Video r-THREE, Operating Instructions Manual

Search results

Summary of Contents for r-THREE

Reviews:

Related manuals for r-THREE

Brands by name

Popular brands