background image

r3a-x2.0

                                                                          

 

22 

 

In addition, the Pan/Tilt Joystick also acts as a button.  
Each time it is pressed (you’ll hear a click), the Pan 
Speed Indicator on in the Display will switch the 
maximum Pan speed from 

NORM

 (default) to 

FAST

 

to 

SLOW

.  Pans speed will run from a 0 to this 

maximum speed such that the more you push the 
joystick, the faster the pan movement will go. 
 
The pan/tilt joystick defaults are configurable – see 
the Advanced Operations (

Configure PanTilt

 and 

System Configuration

 in Table 1). 

 

Zoom/Focus Joystick 
The joystick on the right provides Focus (right & left) 
as well as Zoom (forward & backward).  If you are 
moving the joystick up or down to Zoom, this will 
have priority over any simultaneous left or right 
movement to Focus.  Thus, Zoom has priority over 
Focus to ensure that you do not inadvertently lose 
your focus when zooming in.  
 
In addition, the Zoom/Focus Joystick also acts as a 
button.  When pressed (you’ll hear a click), the focus 
indicator on in the Display will change to indicate if 
the camera is in manual focus or auto focus.  The 
Focus Indicator on the Display will show 

 

FN

 or 

FF

 when the camera is in manual focus and 

you are actively moving the Focus joystick right or 
left. 

 

AF

 when the camera is in auto focus.  Some 

cameras may not be able to communicate the state 
of the auto focus to the 

r-THREE 

system and yet the 

camera may well be in auto focus mode.  So, if the 

AF

 indicator does not come on, you will probably 

Summary of Contents for r-THREE

































































Reviews: