Grizzly Pro Video r-THREE Operating Instructions Manual Download Page 8

Page: 8 / 64

r3a-x2.0

Options and Accessories

Pan Tilt Head

For additional remote cameras, the following is needed:

Up to three

r-THREE

Pan Tilt Heads are supported.

Optional Powered Monitor Cable

(for

r-THREE

and

r-THREE-LS

only)

If using a monitor with a power specification of 12V at no
more than 0.75A, we highly recommend our powered
monitor cable. The

r-THREE

Interface Box can provide the

needed power for up to two monitors, if such a cable is used.

We recommend the Marshall 5.6 Pro Monitor, though other
monitors that draw 12V @ no more than 0.75A and take a
composite input should work.

Powered
Monitor
Cable

r3a-moncable

[rca or phone]

r-THREE

PanTilt

Head

r3a-ptzcam-rca

r3a-ptzcable

[50’, 100’ or 300’]
(300’ shown on Jack Reel)

Summary of Contents for r-THREE

































































Search results

Summary of Contents for r-THREE

Reviews:

Related manuals for r-THREE

Brands by name

Popular brands

Grizzly Pro Video r-THREE, Operating Instructions Manual

Search results

Summary of Contents for r-THREE

Reviews:

Related manuals for r-THREE

Brands by name

Popular brands