139
List of Insert Effects
Chorus –
Gotharman's special chorus with an added Deep parameter, that adds space to the
chorus.
Distortion –
4 types: Valve, Sine, Fuzz, Xdis.
Bit Crush –
Lowers the sample rate and the bit resolution of the sound, to obtain lo-fi effects.
Pitch Shifter –
Shift the pitch of the sound up to 4 octaves up or down, without changing the time
resolution or “tempo” of the sound. Adjustable sense.
Resonator –
Simulates the resonances that comes, if a sound goes through a small box. LD3’s
resonators are synthetic, with more focus on making sounds, than on simulating actual boxes.
Stretcher –
Tries to time stretch the input signal, while at the same time keeping up with it.
Impossible? -Yes, indeed :-)
FM –
Adds self-FM to the input signal in +/- 1 octave, +/- 2 octaves or +/- 4 octaves ranges.
Glitch Shifter –
Imperfect pitch shifter.
Glitch Shifter 2 –
Imperfect pitch shifter with a slightly different sound than the first one.
Glitch Shifter 3 –
Imperfect pitch shifter with a slightly different sound than the first two.
Pitch Shaper –
1 input version of Gotharman's special Pitch Shaper, that forces an audio signal to
play back at a specific pitch, determined by an adjustable frequency.
FAT -
Adds up to 3 layers of the sound to itself, and it is possible to adjust the phase of these, and
to select whether the effect sound should be boosted or just layered.
Filter -
This is exactly the same filters, as can be found in the synth parts. They were added to the
insert effects section, in order to make it possible to filter external signals, to build an LD2 style
filterbank, using multiples of these, and because sometimes it is handy to filter some parts of the
other effects or the analog filters out.
Filters 2 -
A different set of digital filters, that is emphazised in the bottom bass area, and has a
pretty uncontrollable resonance.
Summary of Contents for Little deFormer 3
