274
CCout:
Ext, Int. Sets if the controller track CC’s/Pitch Bend’s should be transmitted to an external
MIDI device via MIDI Out (Ext), or to an internal Synth Part (Int). Regardless of this setting, the
controller track are always available as internal modulation sources.
Quan:
This can be set to either:
-Off:
No quantization of the controller track output.
-1v
: The whole value range of the output of the controller track is quantized to 1V per octave,
when assigned as a source for the CV outputs.
-1.2v:
The whole value range of the output of the controller track is quantized to 1.2V per octave,
when assigned as a source for the CV outputs.
-1vS:
Each value step of the controller track output represents one CV note, at 1v per octave,
when assigned as a source for the CV outputs.
-1.2vS:
Each value step of the controller track output represents one CV note, at 1.2v per octave,
when assigned as a source for the CV outputs.
PLEASE NOTICE:
The scaling of the CV quantization can be adjusted. Please see “Adjusting the CV
scale” a few pages later.
Start:
1 to 128. Sets the track start step. This will be the step, the track starts at, when hitting the
Start/Stop button, or when entering this preset from another preset, while the sequencer is
running.
The Start step can be set globally for all tracks at the Seq Main page.
PrCh:
Off, 1 to 128. When setting the PrCh parameter to any value between 1 and 128, a program
change message will be transmitted on MIDI out, on the MIDI channel selected by the Chan
parameter, every time this preset is selected. The CCout parameter has no effect on this.
Each of the 32 controller tracks can transmit its own program change.
Smooth:
Off, On. When this is set to On, extra controller values will be added between the
controller value steps, to ensure smooth transition between these.
Summary of Contents for Little deFormer 3
